Comments on: Two Super Sizzlin’ Ways to Shape… Using SolidWorks Loft to Point http://www.solidsmack.com/solidworks-loft-to-point-using-spline-on-surface-and-thru-surface/2009-11-03/ Rockin' SolidWorks 3D CAD CAM and Engineering Design Tue, 16 Mar 2010 07:29:09 -0500 http://wordpress.org/?v=2.9.2 hourly 1 By: 3D CAD News and Tips « ThisGlobe.com http://www.solidsmack.com/solidworks-loft-to-point-using-spline-on-surface-and-thru-surface/2009-11-03/comment-page-1/#comment-31663 3D CAD News and Tips « ThisGlobe.com Thu, 05 Nov 2009 17:44:30 +0000 http://www.solidsmack.com/?p=7035#comment-31663 [...] Video Tutorial: Two ways to loft to a point (pictured above) New in SW 2010: The Save Modified Documents [...] [...] Video Tutorial: Two ways to loft to a point (pictured above) New in SW 2010: The Save Modified Documents [...]

]]> By: Josh M http://www.solidsmack.com/solidworks-loft-to-point-using-spline-on-surface-and-thru-surface/2009-11-03/comment-page-1/#comment-31658 Josh M Thu, 05 Nov 2009 15:09:30 +0000 http://www.solidsmack.com/?p=7035#comment-31658 Hey Kieran! Thanks. yeah, should have probably touched on that with the previous post. To get a rounded tip I'd usually do a very smaller matching profile on the other end and use a face fillet or dome. have you tried that? Hey Kieran! Thanks. yeah, should have probably touched on that with the previous post. To get a rounded tip I'd usually do a very smaller matching profile on the other end and use a face fillet or dome. have you tried that?

]]> By: У тебя этого нет… http://www.solidsmack.com/solidworks-loft-to-point-using-spline-on-surface-and-thru-surface/2009-11-03/comment-page-1/#comment-31618 У тебя этого нет… Wed, 04 Nov 2009 22:51:22 +0000 http://www.solidsmack.com/?p=7035#comment-31618 [...] Video Tutorial: Two ways to loft to a point (pictured above) New in SW 2010: The Save Modified Documents [...] [...] Video Tutorial: Two ways to loft to a point (pictured above) New in SW 2010: The Save Modified Documents [...]

]]> By: Kieran Choy http://www.solidsmack.com/solidworks-loft-to-point-using-spline-on-surface-and-thru-surface/2009-11-03/comment-page-1/#comment-31607 Kieran Choy Wed, 04 Nov 2009 12:39:47 +0000 http://www.solidsmack.com/?p=7035#comment-31607 Surprised you haven't mentioned anything about Lofting to a point and setting the end condition Normal to profile...<br><br>1. Create a circle<br>2. Draw a centerline ala tentacle, etc. piercing the center of the circle<br>3. Create a plane normal to the centerline curve at the other end.<br>4. Place a point on a sketch on the plane<br>5. Create the loft, but set the end condition for the point sketch as Normal to profile<br><br>Viola! instant rounded tip! Surprised you haven't mentioned anything about Lofting to a point and setting the end condition Normal to profile…

1. Create a circle
2. Draw a centerline ala tentacle, etc. piercing the center of the circle
3. Create a plane normal to the centerline curve at the other end.
4. Place a point on a sketch on the plane
5. Create the loft, but set the end condition for the point sketch as Normal to profile

Viola! instant rounded tip!

]]>